Philips Service Menu

[psychonate]

Anyone know how to enter the service menu on a philips rear projection TV, I have a 43pp9202.

[Skyway]

Service convergence menu on my Philips is:

0-6-2-5-9-7-Menu

[keving]

Question: What do you do once you're in there? (:

I have a 55, and when I press that sequence, it just puts some letters up on the screen (SMD, or SDM, or something like that).

[Skyway]

On my set I get a convergence settings menu

I have a 64PP990105

[darthgrice]

062596status enters the service alignment mode on my 34pw8520

[RKR0923]

I get the same as keving on a 55PW9363

[Freddy Basset]

On my older 34PW9815, I use 062596 info+.

Let's be careful out there. :whistle:

[jak2812]

hi
i have a little problem, i have the tv with screen one finger narrow in both sides, if i go in to service menu with 062596 + info, in geometry/horizontal there is not any e-w correction (very strange) then i put one eprom from another similar chasis and i have e-w correction but not posible to tuning chanels, i buy a new eprom but i have the same problem like the original one, no appears e-w correction in the menu.
I have seen in the net, in top of the service menu appears several numbers called op1 to op7, and depends the tv model it change, i put the numbers more similars to my tv model, i put the tv in stand by for store this ( there is not any store function in the service menu and i have read in some models with stand by i store the changes), but when i swith on again the tv, the screen is very narrow (like 4:3 format), i can tunning channels and i have in the service menu e-w correction, i adjust it and then the screen is perfect.
I put it in stand by for store the changes, but when i switch on again , the screen is very narrow like when i change the op numbers.
I test another thing, change the op numbers, adjust e-w , return to original op numbers, stand by, switch on again and surprise, i have a good screen, stand by, switch on and again good screen, but surprise, if i switch off the tv from the power button i loose all the parameters and return to the beginning.
I don't know what to do, if are necessary special op numbers for each tv, if there is some special way to store the changes, etc.
Any help is wellcome, i'm lost
thanks

[andy_bernstein]

Hello,

I just bought the 30PW8402 and I would need to know how to get into the service mode to:

- reduce the overscan

- get rid of the garbage bar I get at the bottom of the screen when I output PAL (yes, the 30PW8402 can play PAL !!!). Please note that this garbage bar doesn't show up when I switch on the concerned AV input but only a second or two later (IMHO - this probably can be fixed within the service mode).

Thanks for all !

[Freddy Basset]

Andy,
My older post might help:

http://www.hdtvoice.com/voice/showthread.php?t=8917

[hdrichard]

does anyone know how to into the service menu for a philips 42FD9954
The picture is not centered vertically when displaying an Hd picture from Directv

[doclark]

can someone tell me what has happen to my tv? For some reason when I turn the power on it will come on for about 20 seconds then the power/standby button starts blinking on and off. Can someone help!

[Ratman]

Anything listed in your manual (I.E. Troubleshooting or Error Lights/Indicators)?

[HookemHorns]

Not sure if this is what you need to do but, to reset the T.V. hold down the power button and unplug from the wall at the same time.

[corn]

I want to know the same thing, storing service menu settings on my philips 32" widescreen 32PW4523 :smokin: . please send me your findings, E-Mail at: nzcorn@yahoo.co.nz

[PULLIAMM]

I have a Philips 34P series hdtv. When I am using the component inputs, the adjustment for sharpness in the "personal" mode is disabled, and the fixed value is way too high (84 out of 100.)
Can I change this using the service menu? (Note: the value is lower in some of the preset modes, but they have issues of their own.)
Any help with this will be appreciated.